Impact Crusher Price Guide – How Much Does an Impact Crusher Cost?
Saturday September-05 2026 10:45:18
A 200-ton-per-hour Impact Crusher has a 2026 international market reference price between $40,000 and $180,000, with mobile units costing 30% to 70% more than stationary ones. The exact price depends on capacity, rotor configuration, wear parts material, and automation level. A breakdown by model is provided below.
Introduction
Price quotes for crushers with the same rated capacity can vary by several times across different manufacturers. Equipment configuration, wear parts material, and automation level are the main reasons behind such wide price gaps. This article draws on 2026 public price lists from multiple manufacturers and market research reports, and organizes the information into four dimensions: price ranges, key cost drivers, real-world global case studies, and selection advice.
Impact Crusher Price Ranges
Based on 2026 public quotations from several manufacturers, reference prices for new stationary units are as follows:
- PF-1010, 50–80 TPH: $21,000–$35,000
- PF-1210, 70–120 TPH: $35,000–$50,000
- PF-1214, 100–180 TPH: $40,000–$60,000
- PF-1315, 160–250 TPH: $55,000–$80,000
- Units with capacity exceeding 300 TPH may cost over $500,000
Mobile crushers are typically 30% to 70% more expensive than their stationary equivalents. A high-end tracked mobile unit such as the Metso Lokotrack LT1213S is priced in the $185,000–$245,000 range. On the used equipment market, a nearly-new PF1210 model is quoted at around RMB 120,000–200,000. All prices above are based on Q2–Q3 2026 public listings and are for reference only; actual quotations depend on final specifications.
Key Factors That Determine Impact Crusher Prices
Behind every price difference lie five hard specifications: capacity, rotor, wear parts, automation, and mobility.
Capacity and size. Higher throughput requires larger frames, heavier bearings, and more powerful motors, which can multiply the manufacturing cost.
Rotor material and balancing. Precision-balanced rotors made of high-grade alloy steel cost more, but they effectively prevent bearing failures and frame cracking.
Wear parts material. High-chromium cast iron blow bars offer superior hardness and wear resistance compared to conventional manganese steel, especially for abrasive materials like asphalt recycling or natural stone. With 15%–25% chromium content, they last longer in hard-rock applications. In most uses, quality blow bars deliver 1,500–2,000 hours of service; advanced materials such as ceramic composites can extend this further.
Automation features.PLC touchscreen controls, remote monitoring, and hydraulic adjustment systems can add 5% to 20% to the equipment price.
Stationary vs. mobile.Mobile units integrate an undercarriage and independent power pack, which typically adds 30% to 70% to the cost compared with stationary models.
Impact Crusher Model Comparison Table
| Model | Capacity | Reference Price Range | Typical Applications |
| PF-1010 | 50 – 80 TPH | $21,000 – $35,000 | Small recycling sites, pilot lines |
| PF-1210 | 70 – 120 TPH | $35,000 – $50,000 | Medium quarries, concrete recycling |
| PF-1214 | 100 – 180 TPH | $40,000 – $60,000 | Medium-scale mining, aggregate production |
| PF-1315 | 160 – 250 TPH | $55,000 – $80,000 | Large quarries, fixed production lines |
| Mobile LT1213S | ~250 TPH | $185,000 – $245,000 | Multi-site transfers, demolition waste recycling |
Source: 2026 public price lists from multiple manufacturers
The table shows that model selection directly affects the investment scale. PF-series horizontal shaft units are suited for secondary and tertiary crushing; mobile units cost more but are ideal for job sites that require frequent relocation.
Real-World Global Case Studies
Case 1: Lea County, New Mexico – Road Materials Project
The county road department tested a rented Metso LT1213S tracked mobile crusher starting in October 2024. Over 24 working days, the unit produced 36,303 tons of finished material, reducing production costs to $8.09 per ton. The county estimated a payback period of 2 to 3 years and officially approved its purchase in January 2025.
Case 2: Recicam – Construction Waste Recycling, Spain
Madrid-based Recicam, a family-run construction waste management company, introduced a Metso Lokotrack LT1213S unit to process concrete and demolition debris. The machine integrates magnetic separation for ferrous metals and air classification for plastics and insulation, allowing crushing, screening, and contaminant removal in one pass. Fuel consumption and blow bar wear showed notable decreases, and per-ton production costs dropped considerably compared with the old equipment.
These two examples – road construction and CD waste recycling – demonstrate the equipment's operational performance under different feed materials.
How to Choose the Right Impact Crusher for Your Needs
Start with material hardness: this type of crusher performs well on materials with compressive strength below 200 MPa, such as limestone and construction waste. For highly abrasive materials like granite, high-chromium or ceramic-composite blow bars are necessary to extend service life.
Next, consider product shape: when cubical aggregate is required, this machine offers advantages over jaw or cone crushers.
Finally, calculate total cost: include transportation, installation, energy consumption, wear parts life, and downtime losses in your decision. Measure cost per ton of finished product. The Lea County project data show that a properly matched unit can achieve a production cost of $8.09 per ton.
Impact Crusher Frequently Asked Questions
How do I choose between an Impact Crusher and a cone crusher?
The horizontal shaft impactor produces cubical-shaped aggregates and is suitable for medium-hard materials; cone crushers are suitable for hard materials like granite and basalt.
How often do the blow bars on an Impact Crusher need to be replaced?
In most applications, quality blow bars last 1,500–2,000 hours; in hard-rock applications, this may drop to 200–500 hours.
What if the actual throughput of my Impact Crusher is lower than expected?
Check that feed is evenly distributed across the full rotor width and that no oversize material enters the crushing chamber.
How do I address vibration and dust issues with my Impact Crusher?
Vibration usually stems from rotor imbalance – regularly inspect and rotate blow bars. Dust can be controlled by adding a water spray system at the feed and discharge points.
Closing Remarks
The price of this equipment is determined by capacity, rotor quality, wear parts, automation, and mobility. Understanding these variables and matching them to your specific material and operating conditions is the key to selecting the right model. From Lea County in the U.S. to Recicam in Spain, both projects recovered their investment within 2 to 3 years. Before purchasing, shortlist two or three configuration options and evaluate them on a full life-cycle cost basis.
